Enhancements of IC Engines in Real-world Conditions

Enhancements of IC locomotive engines in Real-world ConditionsAatif Shaik, Aditya Upadhyaya R, Gowtham,K N, Sachin B N annul Optimizing locomotive surgical procedure of IC Engines is a very shady field. Other than reputed companies Original Equipment Manufacturers (OEMs), who publish their reports, the sojourn of the industry does not throw much light into aftermarket modification field. As an end-user, a customer deficient to optimize his vehicle in terms of force out, mileage usability is often mislead into acquire products modifying his automobile that depart produce no useful gains.This mini-project depart be done on 2-racker motorcycles ranging from 150cc-350cc. It aims at bridging the gap amid the products and the end-users knowledge of it. It will take on many such optimizing/modifying techniques, such as induction air-filters, spark plugs, exhaust systems, locomotive oils etc., and try to demystify what is actually happening on that point for the use of the utter end-user.This mini-project will involve testing of various parameters of an engine, such as Brake Horse Power, Torque, Exhaust Emissions, deferralManifold Pressure etc., of a totally memory Engine. It is again tested after modifications for the same parameters. The results are then compared to yield an outline of the effect of the modification. Each modification is done separately for the results to be completely independent of each other. All of the tests are conducted in real-world conditions, so as to ensure the reliability of the result. The terminal report (end of the project work) will give a much needed clarity on the modifications will similarly comment on the safety of using such techniques and its cost effectiveness for the end-user.Market placement In a stock motorcycle (factory-made, unmodified), it is so designed that the whole system is as generic wine as possible. That is, it is supposed to be appropriate for a wide-band of end-users. Taking this line, the manufacturers tune down most of the engine parameters in favour of mileage evoke efficiency, as these are the two major parameters that an end-user looks while buying the automobile.As time passes, the user, who now is accustomed to the automobile, might feel the need to enhance and optimize his automobile. He on that pointfore researches about all the modifications that he green goddess do to his automobiles, so as to increase the mental process and efficiency.Parameters for testing Power produced (at the wheels)Torque produced (at the wheels)Fuel efficiencyThese parameters were chosen because of the following reasons Power produced at the wheel was taken, instead of engine power, because this gives an accurate idea of how the motorcycle will perform in the real world. It also includes the losses that will occur due to external conditions, and therefore will give a virtual(prenominal) feel to the test.Torque produced at the wheel was taken, instead of engine tortuosity, b ecause of the same reasons as above, that is, it will give an accurate idea of performance in the real world.Fuel efficiency is an obvious factor and a parameter to be considered, as most endusers will ultimately look at this for their decisions. It gives an indication of how soundly the engine is taking the modifications and will also represent whether the modification done is cost-effective or not.Specifications of modifications apply Results Air filter modification For institutionalise testing, there is a 1.11secdifference in acceleration timings, in partial hinderance conditions. Whereas, there is a 1.24sec difference in acceleration timings with full load condition. In both cases, the modified motorcycles timings were discontinue.For the crispiness of throttle, it was seen that the modified apparatus has a intermit crispiness than the stock frame-up.For initial fuel efficiency, it was seen that the stock setup fared better than the modified setup.For the cold showti meing test, it was seen that there is no difference between stock and modified setup.Dyno test Synthetic Oil modification For load testing, there is a 2.25sec difference in acceleration timings, in partial load conditions. Whereas, there is a 2.17sec difference in acceleration timings with full load condition. In both cases, the modified motorcycles timings were better.For the crispness of throttle, it was seen that the modified setup has a relatively better crispness than the stock setup.For initial fuel efficiency, it was seen that the stock setup fared better than the modified setup.For the cold starting test, the stock setup fared badly, whereas the modified setup.Dyno interrogation Exhaust Muffler modification For load testing, there is a 2.1sec difference in acceleration timings, in partial load conditions. Whereas, there is a 1.65sec difference in acceleration timings with full load condition. In both cases, the modified motorcycles timings were better.For the crispness of t hrottle, it was seen that the modified setup has an extremely good crispness when compared to the stock setup.For initial fuel efficiency, it was seen that the stock setup fared better than the modified setup.For the cold starting test, it was seen that there is no difference between stock and modified setup.Dyno Test Discussions Air Filter The modified setup performed better than the stock setup, because of the extra amount of air going into the engine cylinder. This allowed the fuelinjected to calibrate and add more than fuel to the air-fuel mixture, thereby gaining power.In the modified setup, as there is no restriction, aside from the filter material, the engine was big to suck air to its maximum capabilities, allowing the fuel-injection system to inject more fuel, thereby increasing power and torque. This is seen as the constant increase throughout the power-band.The crispness of throttle was better in modified setup because the lesser obstruction in the intake system, which allowed air to be sucked in freely.Cold-starting was not affected because of the fuel-injected system, which automatically calibrates the appropriate amount of fuel to be injected in all conditions.Synthetic Oil The modified setup performed better than the stock setup, as the synthetic oil gives better lubrication than the stock setup.This is due to the inherent constitution of the synthetic oil, which provides better lubrication and wear-resistance throughout all temperatures with respect to stock mineral oil.The crispness of throttle was better in modified setup because the lesser friction, which allowed that engine to rev freely and quickly.Due to greater lubrication, lesser friction was present, indeed minimizing friction losses, which attributed to the higher power and torque output in the modified setup.Cold-starting was better in modified setup, as the inherent nature of the oil made less viscous allowing it to start freely and quickly, compared to stock setup.The synthet ic oil also kept the engine temperature lower than the stock setup, thus further helping it to work efficiently.Exhaust Muffler The modified setup performed better than the stock setup, as the free-flow exhaust muffler allowed the exhaust gases to flow out more freely than the stock setup.This allowed the piston to grant lesser load on it to push the gases out, therefore giving a higher power and torque output.This can be seen in the consistent increase in power and torque from 3500rpm.As the load on the piston decreased, the engine was allowed rotate freely, thus giving it a more free nature, whereas the stock setup constricted the engine very much.The crispness of throttle was better in modified setup, because of the free flowing gases in the exhaust system, which allowed that engine to push more and more gases out for the same rpm.Cold-starting was not much different compared to stock setup, as the starting depended on initial air-fuel mixture temperature, which doesnt claim af fected by this modification.Final Conclusion It depends on the end-user on whether he wants to do certain modifications. From the results and discussions, we can see a general increase in performance for all the modifications used, provided those are done downstairs correct procedures. These results were fairly satisfying, and also laid to rest some of the general misconceptions that were attached to such modifications. unconnected from power enhancing, the mini-project also tried to bridge the gap between the aftermarket modifications and the customers knowledge of it. dealings with how the actual results of how a modification might work-out and whether their claims were correct. It is concluded that the manufacturers claims of increasing power and performance which are indeed authorized, But the manufacturer also claims increase in mileage which is not true since it comes with of a small drop of mileage. If the end-user can adjust with the drop, then they can find the modificat ions useful.References Effect of pulmonary tuberculosis air filter condition on vehicle fuel economy.By Kevin Norman, Shean Huff, Brian WestUnited States segment of Energy.Synthetics vs Mineral OilsBy A JacksonExhaust Tuning on 4 stroke Engine experimentation simulationBy Gordon P Blair, D.O Mackey , G.F ChatfieldSociety of Automobile EngineersInternal Combustion Engines MIT Open CoursewareProfessor. Wai Cheng